Brightness (nits)
3 min read · Updated November 12, 2026
Definition
Brightness, expressed in nits, is the measure of a display's luminous intensity per square metre. For digital signage and TV dashboards, nits indicate how well content will remain visible under different ambient lighting conditions, whether mounted indoors near windows or in direct outdoor sunlight.
A nit is one candela per square meter, and the number on the spec sheet decides whether a screen is readable in the room it will actually live in. Too low and content washes out. Too high and you pay for power and heat you did not need.
Key takeaways
Indoor sites without direct sun typically work at 250 to 700 nits.
Windows and semi-outdoor spots call for 700 to 1,000 nits.
Direct-sun outdoor screens typically need 1,000 to 5,000 nits.
Test candidate screens on site, because measured brightness matters more than peak spec figures.
Typical brightness by location
These ranges are a starting point. Reflectors, viewing angles and content type shift the right number up or down.
| Location | Typical nit range | Notes |
|---|---|---|
| Corridors and back-office dashboards | 250 to 400 | Enough where there is no direct daylight |
| Meeting rooms, lobbies and break areas | 250 to 700 | Comfortable in controlled indoor light |
| Window-facing or covered walkways | 700 to 1,000 | Daylight and glare become the main problem |
| Outdoor, direct sun | 1,000 to 5,000 | Depends on reflector characteristics and viewing angles |
Why the number matters
Brightness decides whether a display stays legible against ambient light. In heavy daylight, reflections and glare wash out content on low-nit screens. Finish matters too: a matte finish reduces reflections but can slightly lower perceived contrast, which a higher nit rating can offset.
For workplace dashboards, legibility at a glance is the goal. Small type, alerts and KPIs need contrast, especially where staff move between bright and shaded zones. More brightness can also extend the effective viewing distance, so content stays readable from further away without enlarging fonts.
Choosing a rating
- 1
Find the worst-case light
Identify the maximum ambient light during operating hours, including times when sun hits the screen.
- 2
Match the range
Use the table above as a starting point for the location.
- 3
Consider content
Text-heavy dashboards and detailed charts need more brightness than simple images or video.
- 4
Allow for distance and height
Screens mounted high, or read from far away, need a higher specification.
- 5
Check power and heat
Brighter panels use more power and may need better ventilation or sturdier mounting.
Software can claw back the cost
Use scheduling, brightness profiles and darker templates where suitable. Dim during off-peak hours, and use ambient light sensor integrations where the hardware supports them. See adaptive brightness for how this works.
Verify before you buy in volume
Heat is the trade-off. Brighter screens draw more power and run hotter, which matters most for large-format installations that run 24/7. Many modern commercial displays include ambient light sensors, which help hold visibility while saving energy and extending panel life.
Where you can, trial candidate screens in place and measure real-world performance, not only the peak figure on the data sheet. For very bright environments, see high-brightness displays, and for glare control, anti-glare coatings.
Frequently asked questions
How many nits do I need for a window display?
Is higher always better?
Do I need a sensor?
Related terms
Explore more definitions from the digital signage wiki.
Bluetooth beacons
Bluetooth beacons are small battery-powered devices that broadcast Bluetooth Low Energy signals to nearby receivers. They transmit identifiers which mobile apps or signage systems use to estimate proximity and trigger contextual actions, such as displaying targeted messages on TV dashboards, wayfinding cues, asset tracking updates, or location-based analytics.
Learn more →Bluetooth device pairing
Bluetooth device pairing is the procedure that establishes a trusted wireless connection between a TV dashboard or digital signage player and a Bluetooth peripheral such as a keyboard, speaker, beacon or sensor. The process exchanges identity and encryption keys so devices can authenticate, bond and communicate reliably within a managed Fugo signage deployment.
Learn more →Brightness uniformity
Brightness uniformity describes the evenness of luminance across a display, measured as the relative difference between the brightest and darkest areas. It is a practical quality metric for TV dashboards and digital signage that influences readability, perceived colour consistency and the integrity of brand assets across a signage network.
Learn more →